Setting up your Whisp 50

The Whisp 50 is a powerful scenting platform designed to connect directly to your HVAC  system. With precision timing controls and intelligent diffusion technology, it gives you complete command over when and how scent fills your space. Follow the steps below to program your Whisp 50 for your space.

Before You Begin

Ensure your Whisp 50 is properly installed, connected to power, and the LED display is active.
You’ll use the same four control buttons throughout setup:

  • MODE – cycles through programming modes
  • SET – selects items and confirms changes
  • ▲ (UP) – increases values
  • ▼ (DOWN) – decreases values

When the screen displays WORK ON, your Whisp 50 is actively diffusing scent. When it shows PAUSE ON, the unit is in a resting phase. PAUSE OFF means the unit is fully stopped.

Step 1 – Set the Clock and Workdays

  1. Press SET until the hour digits begin to flash.
  2. Use ▲ / ▼ to adjust the time.
  3. Press SET again to move to minutes and adjust as needed.
  4. Press SET again to move to workday selection.
  5. Use ▲ / ▼ to choose which days your Whisp will operate (for example: Mon–Fri, Mon–Sun, or Weekend only).

This ensures your scent schedule aligns with your daily routine.

Step 2 – Set Your Scent Schedule

Your Whisp 50 can store up to four programmable periods per day. Each period defines when the device runs and pauses.

  1. Press MODE to enter the first period setup.
  2. Press SET to begin editing.
  3. Adjust the start time (hour + minute) with ▲ / ▼.
  4. Next, set your Work Time (the misting duration) — anywhere from 5 to 300 seconds.
  5. Then set your Pause Time (rest duration) — anywhere from 5 to 900 seconds.
    Press MODE again to save and move to the next period (2, 3, or 4) if desired.

Default Settings

Your Whisp 50 ships with the following default program:

  • Active: 8:00 AM – 10:00 PM
  • Days: Mon – Sun
  • Work: 60 seconds
  • Pause: 120 seconds

Only one period (Period 1) is active out of the box, which runs your device all day long at the above intervals. This is often too much for most spaces. To start out slow, try a schedule like the following:

  • Period 1
    • Active: 8:00 AM – 8:20 AM
    • Days: Mon – Sun
    • Work: 60 seconds
    • Pause: 120 seconds
  • Period 2
    • Active: 11:00 AM – 11:20 AM
    • Days: Mon – Sun
    • Work: 60 seconds
    • Pause: 120 seconds
  • Period 3
    • Active: 3:00 PM – 3:20 PM
    • Days: Mon – Sun
    • Work: 60 seconds
    • Pause: 120 seconds
  • Period 4
    • Active: 6:00 PM – 6:20 PM
    • Days: Mon – Sun
    • Work: 60 seconds
    • Pause: 120 seconds

This is just a sample schedule for coverage throughout the day. Adjust as needed for your space and preferences.

Step 3 – Lock or Reset Your Settings

  • To reset everything: Hold MODE for 10 seconds.
  • To lock your program: Hold MODE + SET together for 5 seconds until “LOCK” appears.
  • To unlock: Repeat the same combination again.

Locking prevents accidental changes once you’ve dialed in your ideal settings.

Step 4 – Fan Control (Optional)

If you prefer a quieter operation, you can manually control the internal fan. To do so, follow the instructions below:

  • While the current time is displayed, hold ▼ (DOWN) for 5 seconds to turn the fan off (screen shows “F0”).
  • Hold ▼ again for 5 seconds to turn the fan on (screen shows “F1”).

Pro Tips

  • Start with lower intensity and increase gradually.
  • Once you've dialed in your preferred scenting schedule, record your settings for each scent, as they can each have varying levels of intensity.
  • Clean your oil canister every few months to keep diffusion consistent.

Step 5 – Enjoy!

Once programmed, your Whisp 50 will automatically maintain your schedule — turning scent diffusion on and off throughout the day to keep your space perfectly balanced.

👉 Continue to the next article: Fine-Tuning Your Scent Distribution

Back to blog